AXD000002-DDB

Dust Deputy Bagger Cyclone Separator Kit

$149.95

Original, patented, cyclone design stops up to 99.9% of fine dusts and bulk debris from clogging your vacuum's filter - eliminating suction loss while saving you time and money on expensive replacements! Bagger kit is perfect for stationary setups near the workbench!

Upgrades any make/model shop vacuum with 1.5" to 2.5" hose fittings.
Neutral-vane technology improves separation efficiency by 20%.
Steel wall-mount saves valuable floor space - ideal for small shops.
High capacity dust bags show a visible fill level for emptying.
6-foot hose and elbows connects easily to standard shop vacuums.
Anti-static components significantly reduce the likelihood of static shocks.

Skip to the end of the images gallery

Dust Deputy Bagger Cyclone Separator Kit

Skip to the beginning of the images gallery

Overview

Eliminate Suction Loss With Any Wet/Dry Vacuum

The original and still the best! Now 20% more efficient with Neutral Vane Technology, the Dust Deputy® Bagger lets you work the way you want to. Injection molded from a translucent anti-static resin, the patented design of the Dust Deputy cyclone uses centrifugal force to capture and remove 99% of dust and debris from the air-stream before it reaches your vacuum's filter, eliminating clogged filters and suction loss!

How It Works:

The dust-laden air passes through the Dust Deputy Cyclone, which separates out up to 99.9% of the dust. The cleaned air passes into your shop vacuum, while the dust falls into an accumulation bin with an open grid bottom.

A heavy (4 mil thick) plastic bag is held in place around the accumulation bin. When the vacuum is turned on, the bag is sucked up against the grid. When the vacuum is turned off, the bag drops back down and the collected dust falls from the accumulation bin into the bag. When the vacuum is turned on again, the previously bagged dust remains in the bag while newly captured dust collects in the accumulation bin.

This action can be repeated until the bag is two-thirds full, at which point the bag should be removed and replaced.

The Dust Deputy Bagger Kit Includes:

Anti-Static Dust Deputy Cyclone Separator
Powder-Coated Steel Wall Mount Bracket
3.9-Gallon Accumulation Bin
Steel Grid
Five 4 Mil Thick 28" x 40" Bags
Two Silicone Rubber Bands
2" x 6' Vacuum Connection Hose
Two 90 Degree Hose Elbow Adapters
2.5" Adjustable Hose/Band Clamp
Two Foam Gaskets
Hardware

See the Dust Deputy Bagger in action!

Check out these great reviews and installation videos shared by our customers!

Watch Gradually Wizardly open and install the Dust Deputy Bagger.

See a Dust Deputy Bagger demonstration from Home Improvement & Repair.

Specifications

More Information
SKU	AXD000002-DDB
Cyclonic Separation Efficiency	Removes over 99% of fine wood dusts
Waste Capacity	Customizable
Inlet Size	2" O.D. (Tapered) 1-3/4" I.D.
Outlet Size	2" O.D. (Tapered) 1-3/4" I.D.
Discharge Size	3" I.D.
Primary Build Materials	Polypropylene
Welding	N/A
Static Resistance Rating	Anti-Static
Color	Clear
Depth	12-3/4"
Height	24-1/2"
Actual Weight	13
Contents	Cyclone, 3.9-Gallon Accumulation Bin, Wall Mount, Steel Grid, 2x Elbows, 2" x 6' Hose, 5x Bags, 2x Rubber Bands, 2x Gaskets, & Mounting Hardware
Manufacturer	Oneida Air Systems
Manufacturer Statement	Made in USA
Warranty Information	1 Year Limited Warranty
Proposition 65	WARNING: This product may expose you to chemicals, including Nickel (metallic), which is known to the State of California to cause cancer or birth defects or reproductive harm.

Documents

Videos

All-Clear Components

How Cyclone Separators Work

How to Assemble the Deluxe Kit

Cyclonic Separation Efficiency

Dust Deputy vs Dustopper Comparison

Air Velocity Testing

Product Overview

FAQ

How do I prevent my bucket from collapsing with my Dust Deputy or Low-Pro?

Ensure your bucket is not old, damaged, or thin-walled. To increase the strength of a thin-walled bucket, you can stack two buckets together. Two stacked thin-walled buckets will work well to avoid bucket collapse. Ideally, we recommend a bucket with a 90 mil wall thickness or higher. A 90-mil or higher walled bucket will completely avoid bucket collapse.

What vacuum do you recommend for the Dust Deputy?

The Dust Deputy can be used with any make, model, or size wet/dry vacuum with an inlet ranging from 1.5" to 2.5" in size. We recommend that it has an airflow rating of at least 50 CFM to ensure optimum dust separation performance.

How do you fasten the conductive metal tape to the plastic cyclone?

You'll want to apply the tape so that all three openings on the cyclone are connected by a continuous, conductive path. When doing so, make sure that the tape is wrapped over the edge of the cyclone's ports and that it overlaps the bolt hole on the cyclone's bottom flange. Click "Read More" for further instructions and images.

Will the Dust Deputy cyclone work if my tool has its own fan blower?

In most cases, yes - but the cyclone's efficiency will vary based on whether your vacuum is also turned on. The Dust Deputy cyclone needs a consistent airflow rate to "spin" the dust out of the airstream; If your tool's fan blower is pushing air in while your vacuum is also sucking air out, this can disrupt the airflow rate and reduce the cyclone's separation performance. In many cases, the fan blower on tools (such as planers) cannot be turned off. If that is the case for you, try collecting your dust with the vacuum turned off. In doing so you will be creating a positive pressure system as the tool's fan blower pushes air through the Dust Deputy cyclone. This method may not work with every vacuum

How do I troubleshoot an air leak with my Dust Deputy cyclone?

Even a small leak can significantly affect the overall separation performance of the cyclone. If you can't audibly pinpoint where the leak might be coming from, one of the simplest ways to check for air leaks is with a smoke test. Click "Read More" for further instructions and tips.

How should the Dust Deputy be grounded?

Apply conductive metal tape to the cyclone. For added grounding, attach a wire with a washer tied to one end when installing one of the bolts at the base of the cyclone. Click "Read More" for further instructions.

What is an anti-static material?

This term refers to the range of conductivity that a material has. Anti-static materials range from 1010-1012 Ohms. More information about static resistance can be found here.

Can I use the Dust Deputy with my 4" hose / port?

No. The standard Dust Deputy cyclones are designed for use with ports/hose that are 1" to 3" in diameter. Connecting 4" tools to the Dust Deputy cyclone's 2" ports will result in significant losses in airflow and suction power. Larger ports (4" and larger) will instead require one of our Super Dust Deputy cyclones.

Can I use this cyclone with smoldering or abrasive debris?

No. This cyclone is designed for use with light debris such as wood dust. For heavy-duty applications with highly abrasive or smoldering materials, we recommend our steel, Heavy-Duty Dust Deputy kits instead.

Can I remove the top portion of the Dust Deputy?

No, it is not advised. This can cause damage to the cyclone and is not covered under warranty.

What is the minimum air watts needed for the Dust Deputy?

Rather than worrying about what specs your vacuum needs (e.g. air watts, cfm, static lift, etc.), we at Oneida Air Systems have a much simpler approach - simply match the size of your vacuum's inlet to the size of the Dust Deputy cyclone's ports. The Dust Deputy cyclone's tapered 2" ports are designed to work with any make and model wet/dry vacuum on the market today, regardless of horsepower, wattage, etc. Most vacuums will have an inlet ranging from 1.5" to 2.5" in diameter - perfect for our cyclone. Keep in mind that every component installed onto your vacuum will have an effect on the system's suction power. That includes your hose, hose attachments, adapters, elbows, couplers, etc.

Can I use this upstream of a 650 CFM jet tools bag type dust collector?

No. The smaller Dust Deputy cyclone are intended for use with HIGH pressure and LOW airflow systems, such as wet/dry vacuums, with port sizes 2.5" diameter and smaller. It would not be suitable for your HIGH airflow, LOW pressure system (i.e. dust collectors). You would want to look at our line of Super Dust Deputy cyclones instead. Match the cyclone based on the size of your dust collector's intake.

How do I connect the Dust Deputy to a snap-on inlet?

Other adapters may be necessary to connect the Dust Deputy to non-standard sized or locking-type inlets. Click "Read More" to see adapter suggestions.

Product Guide

Dust Deputy Bagger Cyclone Separator Kit

Eliminate Suction Loss With Any Wet/Dry Vacuum

How It Works:

The Dust Deputy Bagger Kit Includes:

Real Reviews From Fellow Craftsmen